Jim Loring's guest appearances

Jim Loring

HVAC School - For Techs, By Techs

Kevin Hart

Bill Johnson

Ruth King

Chris Stephens

Dan Holohan

John Ellis

Bill Spohn

Jack Rise

Andy Holt

Jerry Eavenson

Nate Adams

David Richardson

Jim Bergmann

Jamie Kitchen

Corbett Lunsford

OwlTail

In today's podcast episode, Bryan talks to west-coast commercial tech Jim Loring about pneumatic controls and variable air volume (VAV) systems. People sometimes confuse pneumatics and hydraulics. Hydraulics use liquid to provide pressure; conversely, pneumatics use air to provide pressure. Pneumatic controls use a bit more energy than other controls, but they are less costly all around. Nowadays, direct digital controls (DDCs) provide greater energy savings than pneumatics. However, pneumatic controls were a precursor to the DDC technologies we use on actuators today, and they are still a prevalent technology. The air compressor is a critical component of pneumatic controls. That is because pneumatic controls require clean, dry air. Air compressors have an auto-drain and auto-dryer to help purify the air for peak performance. However, while air compressors are basic, their maintenance practices are often overlooked. Variable air volume (VAV) units vary airflow throughout the building via zones. Each zone has a damper and a thermostat. The thermostats control the dampers, which control airflow to the zone and move via actuators. In a pneumatic control system, the air pressure release or gain at the thermostat moves the dampers. Thermostats also have to bleed off some of that air via direct or reverse-acting controls. Bypasses help regulate static pressure when dampers close. Thermostats can help modulate the dampers; they don't merely open and close. The modulation occurs within a certain pressure range on a VAV system. (For example, 8 PSI would close the damper while 13 PSI would leave the damper wide open.) In addition to damper modulation, velocity controllers help control the air velocity based on signals from the thermostat. Jim also covers:  Common air compressor problems Pressure-reducing valves (PRV) Restrictor tees Direct-acting vs. reverse-acting controls Heating and cooling in VAV systems Damper position If you have an iPhone, subscribe to the podcast  HERE, and if you have an Android phone, subscribe  HERE.

In today's podcast episode, Bryan talks to west-coast commercial tech Jim Loring about pneumatic controls and variable air volume (VAV) systems. People sometimes confuse pneumatics and hydraulics. Hydraulics use liquid to provide pressure; conversely, pneumatics use air to provide pressure. Pneumatic controls use a bit more energy than other controls, but they are less costly all around. Nowadays, direct digital controls (DDCs) provide greater energy savings than pneumatics. However, pneumatic controls were a precursor to the DDC technologies we use on actuators today, and they are still a prevalent technology. The air compressor is a critical component of pneumatic controls. That is because pneumatic controls require clean, dry air. Air compressors have an auto-drain and auto-dryer to help purify the air for peak performance. However, while air compressors are basic, their maintenance practices are often overlooked. Variable air volume (VAV) units vary airflow throughout the building via zones. Each zone has a damper and a thermostat. The thermostats control the dampers, which control airflow to the zone and move via actuators. In a pneumatic control system, the air pressure release or gain at the thermostat moves the dampers. Thermostats also have to bleed off some of that air via direct or reverse-acting controls. Bypasses help regulate static pressure when dampers close. Thermostats can help modulate the dampers; they don't merely open and close. The modulation occurs within a certain pressure range on a VAV system. (For example, 8 PSI would close the damper while 13 PSI would leave the damper wide open.) In addition to damper modulation, velocity controllers help control the air velocity based on signals from the thermostat. Jim also covers: <ul> <li>Common air compressor problems</li> <li>Pressure-reducing valves (PRV)</li> <li>Restrictor tees</li> <li>Direct-acting vs. reverse-acting controls</li> <li>Heating and cooling in VAV systems</li> <li>Damper position</li> </ul>If you have an iPhone, subscribe to the podcast <a href="https://itunes.apple.com/us/podcast/hvac-school-for-techs-by-techs/id1155660740?mt=2" rel="nofollow" target="_blank"> HERE</a>, and if you have an Android phone, subscribe <a href="http://www.stitcher.com/podcast/bryan-orr-3/hvac-school" rel="nofollow" target="_blank"> HERE</a>.

Intro to Pneumatic Controls w/ Jim Loring